Pages

Monday 1 October 2012

Allwinner a13 4.0 firmware And Installation

Hey Guys..
               Lots Of People Have Been Asking Me About Firmwares Of The Allwinner A13 Tablet, Even I've Searched For It On Google But It's Quite Hard To Find, But I Finally Found it,
Click On The Following Link To Download It
http://uploading.com/files/eaf12bc6/Q8A13_51324_new.rar/

Download it And Install It On Your Device
Follow The Instructuions To Install It.

1. Download And Install Live Suit, You Can Donwload It From Herehttp://rockchipfirmware.com/sites/tntfiles/LiveSuitPack_v1.07.zip
2. Open Live Suit
3. Select The Image You Downloaded From The Link
4. With Your Tablet Power Off Hold Volume Up Do Not Release The Volum Up And Insert Usb Cable Into The Tablet.
5. Livesuit Will Detect The Tablet And Ask You What To Do.
6. Follow The Instructions And You're Done.

Enjoy Guyz, And Comment Your Views, Problems Or Questions.

56 comments:

  1. Hi,

    I followed all your instructions but when I connect the tablet (holding volume up) a box with just an exclamation mark opens up within Live Suit and nothing further happens. It then resets the wizard back to the start

    ReplyDelete
    Replies
    1. When LiveSuit is waiting for device, you should disconnect it and connect again by holding volume up...

      Delete
    2. Got the same, rename the image file because it has some chinese signes which livesuit is not accepting.

      Only I 'm stuck in a bootloop now

      Delete
    3. I know the posts are a little old but here is what I did to get LiveSuite to flash my AllWinner a13 (assumes LiveSuite is running):
      1. Turned off the device
      2. While holding Vol Up power up the device
      3. Once device is on, connect it to the pc
      4. Press power button rapidly 10x

      Delete
    4. If you are looking to flash firmware, google

      ET Q8 V1.2 A13Q8 GSL1680 605322 RTL8188 2Cam(MID-756 4.2.0)

      and use PhoenixCardV306 to burn the image file to sd card.

      Place sd card in the tablet and turn on. Don't touch any
      buttons or touch screen until flash finishes.

      I could never get software to recognize the tablet even using
      generic drivers.

      Good luck

      Delete
  2. are you sure you're using allwinner a13, coz it don't work with other tablets.

    ReplyDelete
  3. A13 so many image.. I have 6 image.if u install with wrong image... u tablet not funtion proply

    ReplyDelete
  4. exelente si me funciono me revivio mi alwinner a 13

    ReplyDelete
  5. hello brother firmware compatible in tablet sanei n91 ??????????

    ReplyDelete
  6. Straight after attaching the cable, and whilst still holding down the volume+ button, start pressing the tablet power button repeatedly (approx 1 press per second for 10 seconds is enough). This procedure puts the tablet into update mode. have been told this also works

    ReplyDelete
  7. hi i have tried this with my a13 allwinner 7" tablet and the screen goes straight to a pic of the android on its back with a red exclamatin mark on the front and livesiute does not recognise the tablet is there. Do u know how to get round this?
    cheeers

    ReplyDelete
    Replies
    1. If you're using Windows it must be 32bit or x86 System Architecture, it'll enable you to access your device. I've tried it and works pretty well to me :)

      Best Regards

      Delete
  8. I having the same problem as you chris ridick. Have you found a way to flash your tablet?

    ReplyDelete
  9. Hi,

    Did it work for you? I am using Ubislate 7Ci tablet running ICS 4.0.4. Yet to root the device (Not finding appropriate drivers, so that ADB would detect the device AND not finding appropriate ROOTING tool like LiveSuite).

    Want to first root the device. Can you help me.

    Thanks,
    Joe

    ReplyDelete
  10. Hello.

    This image works on "Sony Q8"? Yes, I know, in name of image is it... but i'm not sure. Anyone ask?

    PS: Sorry for my english...

    ReplyDelete
  11. hi i flashed my tablet but touch screen isnt working so i want to try another firmware but when i try to reflash im just getting exclemation mark from live suite .ive tried diconnecting and reconnecting whilst holding volume up button but it still does the same,any help would be apreciated .thanks,
    Paul

    ReplyDelete
    Replies
    1. just plug in usb mouse and the touch will be up again

      Delete
    2. try this
      http://www.maipad.net/update-softwares/mx913.html

      Delete
    3. same problm touch not working

      Delete
  12. Touch screen hang up on the android picture. Still need to find a compatible firmware. :(

    ReplyDelete
  13. hey I'm using this firmware on my tablet *Schneider Pandora 9.10* work fine but the touch screen not work. please help me.
    I have this tablet *Schneider Pandora 9.10*

    ReplyDelete
  14. just wondered if anyone could help me ive loaded up the pic and as soon as the cable goes into my tablet a little box pops up with a yellow/orange triangle but no message or writing what do i do?????

    ReplyDelete
  15. I could upload my a13 q88 allwinners ics 4.0.4 but the issuse it the build prop is set to show assamsung note 2 and use gingerbrack apk to root a13 I used titum backup and trans some systems apks to it . I would like to no if I can use my old droid chip its qulcoawm or att fuseion windows modom if anyone understand pc boards and chips could I mack this board a slave to my moded a13 ics boxchip . And if you can put android on ios why not make ios a slave board ? Ios is your old apple ipod or iphone that no longer work do to esn why use ios as a ipod make it an app store slave board so get at me on xda un mondayred9 o I'll got a working driver so y'all don't have to use sdk adbplatform tools you can use ginger barke apk form 2shared get sp flash tool v3 .12222.00 form 4shared the flash tools have a unversl usb driver that works say like if you wunt to boot from sd .flash for sd .install update form .sd est yo iam out trying to make old ios a new a13 slave pes

    ReplyDelete
  16. Hi there. the % gets only to 5% on the Livesuit, and stops/resets. Nothing happens on the tablet. What am i doing wrong? thanks for the help in advance, im a n00b :p on Android

    ReplyDelete
  17. Hi guys can someone go to settings and click about and tell me the model number please and thanks? :)

    ReplyDelete
  18. andy_my
    A13 Spesifications (if anyone need it)...
    http://allwinner.com/product/A13.php

    ReplyDelete
  19. This comment has been removed by the author.

    ReplyDelete
  20. tendran los driver de esta tableta ya que mi pc no la reconoce gracias.

    the driver will have this tablet as my pc does not recognize it thanks.

    ReplyDelete
  21. techknow.me has many roms for a13 tablets

    ReplyDelete
  22. I need
    A13
    model mid 2810
    frimware.

    ReplyDelete
  23. KINDLY GIVE LINK FOR UBISLATE 7CI FIRMWARE LINK

    ReplyDelete
  24. i got wifi 8188EUS sun5i_android_a13-baili1214.img file, Allwiner a13 uploaded but touch not working,
    kindly give resolution

    ReplyDelete
  25. need a13 model number a902 firmware plz help

    ReplyDelete
  26. anyone please provide ubislate 7ci firmware. Thanks anyway!

    ReplyDelete
  27. muito bom, finalmente, depois de 6 meses tentando ligar esse tablet ching-ling, consegui, muito obrigado cara.

    ReplyDelete
  28. http://www.86pp.com/download_view.asp?id=889

    Complete Firmware for Allwinner Q88 A13

    ReplyDelete
  29. Thanks for the tip. It worked. I'm not using the firmware you recommended, using device default firmware.

    ReplyDelete
  30. when i plug my tablet , livesuit(not responding) all the time!!!

    ReplyDelete
  31. could you guys, upload the original firmware? it seems I've just lost it and cannot find any...

    ReplyDelete
  32. android TAB a13 allwinner tech D1127CA 2251 firmware image kay full tool link sand give my id chamandeep114@yahoo.com

    ReplyDelete
  33. If you are looking to flash firmware for the 7Ci, google

    ET Q8 V1.2 A13Q8 GSL1680 605322 RTL8188 2Cam(MID-756 4.2.0)

    and use PhoenixCardV306 to burn the image file to sd card.

    Place sd card in the tablet and turn on. Don't touch any
    buttons or touch screen until flash finishes. It flashes
    4.2.0, change language from Thai to your preference.

    I could never get software to recognize the tablet even using
    generic drivers.

    Good luck

    ReplyDelete
  34. can you give me link where i can download livesuit? the link above is not directing me to the download link

    ReplyDelete
    Replies
    1. here you go..... http://rockchipfirmware.com/sites/tntfiles/LiveSuitPack_v1.07.zip
      Enjoy !!

      Delete
  35. Hello, I have stouch s728 Allwinner A13 DB060CA 1BJ1. I have tried a dozen firmwares but the touch doesnt work. Anyone with the right firmware???

    ReplyDelete
  36. pls help me im need share mid 2810 firmware

    ReplyDelete
  37. Mahindra & Mahindra, India's top-selling utility vehicle maker, plans to offer Google's Android Auto technology in its vehicles, a top company executive has said in a statement. To know more about android, Visit Android Training in Chennai

    ReplyDelete
  38. This is most informative and also this post most user friendly and super navigation to all posts... Thank you so much for giving this information to me.. 
    excel advanced excel training in bangalore

    ReplyDelete